Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. 1.2083 Round Bar 1.2083 Flat Bar 1.2083 Hollow Bar 1.2083 Tube / Pipe 1.2083 Sheet / Plate 1.2083 Strip / Coil 1.2083 Wire 1.2083 Forging 1.2083 Tube / Pipe TEL:+86-80247006
Alloy Tool Steel Inc.13525 East Freeway Drive, Santa Fe Springs, CA 90670-5686 Tel:(562) 921-8605 FAX:(562) 802-1728
China 1.2083 4Cr13H Annealed Black Surface Stainless Steel 1.2083 4Cr13H Annealed Black Surface Stainless Steel Flat Bar Product Introduction 2083 is a tool steel in the group of plastic mold and stainless in matesitic (AISI420)So, it can stand for corrosive and can be quench to enhance it's strength together with corrosive resistance properties.
Description DIN 1.2083 / AISI 420 Steel Forged Blocks for Plastic Mould Making Equivalence AISI / SAE DIN / W.Nr JIS GB 420 1.2083 SUS420J2 4Cr13 Chemical Composition (%) Steel Grade C Si Mn P S Cr 1.2083 0.36 0.42 1.00 1.00 0.030
Good Price VD 1.2083 Alloy Steel BarSpecial 1.2083 alloy steel with good price. 1.2083/420/S136 Alloy Tool Steel For Stainless Steel 1.2083 mould steel is a kind of plastic mould steel with high chromium element which is up to 13%.1.2083 mould steel has good wear resistance and good polishing, it
H13, 1.2344, SKD61, 420SS, S7, 1.2083, SUS420J2 ESR tool The Limitations of "Off-the-Shelf" Mold Steels. Many grades of tool steel that are used for building molding components also are used for other industrial applications. For example, AISI S7 and H13 are commonly used for plastic injection molds; however, S7 also is
SKD11 Heat Treating Tool Steel , Tool Steel Round Bar Excellent Machinability. Special Tool Steel. 32 HRC Hardness P20 Tool Steel , 1.2311 Tool Steel Alloy Plastic Mould Steel Sheet. Annealed Special 1.2083 Tool Steel Corrosion Resistant Flat Bar Low Impurity Content. 1.2344 Special Tool Steel Forged Delivery Condition Round Bar Mill Certificated
Plastic Alloy 1.2083H 420H S136H Mould Steel PlatePre Hardened Tool Steel 1.2083H 420H S136H Plastic Alloy Tool Mould Steel Plate . S136 Stainless Tool Steel is a martensitic stainless steel with 12% Chromium which is sufficient to give good corrosive resistance properties. Its best corrosive resistance is when hardened and surface is ground or polished.It has good ductility in the annealed condition but can be hardened up to 500HB
STAVAX ESR - AssabSTAVAX ESR STAVAX ESR (420) (1.2083) (SUS 420J2) MIRRAX ESR MIRRAX ESR (420) MIRRAX 40 MIRRAX 40 (420) POLMAX POLMAX (420) (1.2083) (SUS 420J2) RAMAX HH RAMAX HH (420 F) This classic stainless tool steel is the right choice when rust in production is unacceptable and where requirements for good hygiene are high, as within the medical
Die Steel 1.2083 ESR STEEL Tool steel, mold steel, plastic mould steel, alloyy steel, special steel, die cast steel Pre-hardened to HRC 32-36 For corrosive PVC, acetum fiber and complicate Die Steel 1.2083 ESR STEEL Delivery condition:Pre-hardened to HRC 32-36. Characteristics:- Excellent corrosion resistance - Excellent ductibility and tenacity.
Tool steel as round steel, flat steel and sheet metalCorrosion-resistant, pre-hardened tool steels Here you will find a range of pre-hardened and tempered, corrosion-resistant steels for use with corrosive plastics, e.g. 1.2316, and 1.2085 with added sulphur for improved machinability. 1.2083 provides improved polishability and 1.2083 ESR
Uddeholm Ramax HHProtect the steel and heat through to 740°C (1365°F). Cool at 15°C (30°F) per hour to 550°C (1020°F), then freely in air. STRESS RELIEVING After rough machining the tool should be heated through to max. 530°C (985°F), holding time 2 hours, then cool freely in air. Relative corrosion resistance % 100 75 50 25 Ramax HH W.-Nr. 1.2085
Uddeholm Tyrax ESR has much higher toughness/ductility compared to other stainless tool steel of W.-Nr. 1.2083/AISI 420 type. Approximate room temperature impact strength as measured by samples removed from the centre of a forged block, tested in the short transverse direction is shown below. Original bar dimension:250x80 mm (10" x 3")1.2083 Tool Steel - Tool Steel Specification and Information1.2083 Tool Steel. 1.2083 is a chromium alloyed plastics mould stainless steel, which is characterised by good polishability, good hardenability giving high hardness, with fair corrosion resistance. Forging:Heat slowly and uniformly to 1000°C. After forging cool slowly. Annealing:Heat slowly to 780°C. Slowly cool in furnace. Hardening:Pre heat to 600-700°C until heated through.